// Managed Infrastructure
What Is Structured Cabling? What an Office Build-Out Needs
Structured cabling is the organized cable plant behind your walls and ceilings, the copper, fiber and low-voltage runs installed to industry standards, tested, labeled at both ends and documented, so every desk, access point and camera in the office connects reliably.
What structured cabling includes
Most people picture a network cable at a desk. The cable plant is wider than that: it covers the network itself and the low-voltage systems that share the same walls and ceilings.
| Type of run | What it connects |
|---|---|
| Voice and data copper | Desk drops, phones, printers and access points |
| Fiber | Uplinks, long runs and the high-speed backbone between rooms |
| Coax | Network runs where the design calls for it |
| Low-voltage runs | Security cameras, access control, AV and point-of-sale |
Because one plant covers all of it, one contractor can run one project and hand over one documented plant. Our structured and low-voltage cabling page describes that work.
Why it is organized, not just pulled
The word "structured" is the point. Cable that is simply pulled where it is needed works until someone has to trace it, move it or find out why a connection keeps dropping. Structured cabling is installed to industry standards (BICSI, TIA/EIA), every run is tested, both ends are labeled, and the plant is recorded in as-built documentation that stays with you. When someone traces a cable years later, it makes sense, and future changes are informed rather than improvised.
Cat6, Cat6A or fiber
The right cable depends on distance, speed and how far ahead you are planning. Cat6A is typical for desk drops in modern builds and can carry 10GbE up to 100 meters. Fiber is used for uplinks, long runs and the backbone. The mix is designed around your layout and your horizon, not chosen from a catalog.
When to plan it in an office build-out
Plan cabling during design, before construction starts. Cable paths, the locations of the IDF, MDF and rack room, and power and cooling for the racks all drive later decisions. Cabling planned after the walls close forces compromises and retrofits.
In practice that means involving IT alongside your architect and general contractor: reviewing floor plans, mapping drops for every desk, access point, camera and printer, and setting the install into the construction window so cable is tested before move-in.
What a new office needs around the cabling
Cabling is the first layer, not the whole office. Most new offices need the same core layers:
- structured cabling to every desk, access point, camera and printer location;
- an IDF, MDF or rack room with the power and cooling to support it;
- an internet circuit brought in at the demarc;
- switches, a firewall and Wi-Fi access points;
- the phones, printers and cameras that run on top.
Our office cabling design and build-out service plans those layers as one project. For the rack room itself, see server room modernization and UPS and power continuity.
Existing buildings with unknown cabling
Not every project starts with bare walls. If you have moved into a building with an unknown cable history, or you are planning a major network upgrade, the existing plant can be tested and documented first: what meets current standards is identified, and runs that should be replaced are flagged. Buildings where earlier cable work was done without documentation benefit most.
Cabling is one part of our managed infrastructure work. If you are planning a move or a build-out, talk to our team early, while the drawings can still change.
// FAQ
Common questions
Q
What is structured cabling?
It is the organized cable plant behind your walls and ceilings, copper, fiber and low-voltage runs installed to industry standards, tested, labeled at both ends and documented so it outlives the equipment plugged into it.
Q
What is the difference between structured cabling and low-voltage cabling?
Low-voltage runs for security cameras, access control, AV and point-of-sale are part of the same plant, alongside the voice and data copper, fiber and coax for the network, so one project can cover both.
Q
Should we choose Cat6, Cat6A or fiber?
It depends on distance, speed and how far ahead you plan: Cat6A is typical for desk drops in modern builds, and fiber is used for uplinks, long runs and the backbone.
Q
When should cabling be planned for a new office?
During design, before construction starts, because cable paths, rack room locations and power and cooling drive later decisions, and cabling planned after the walls close forces compromises and retrofits.
Q
What if our building's existing cabling is undocumented?
The existing plant can be tested and documented, so you know which runs meet current standards and which should be replaced, which is useful before a major network upgrade or after taking over a building.
Get the InfoNetworks newsletter
One email a week with our new articles. Unsubscribe anytime. Privacy policy.